Project

General

Profile

Tâche #17344

Scénario #17200: Qualification EOLE 2.6.0 RC1

Scribe 2.6.0rc1 :Erreur au diagnose en utilisant le template etb1.scribe-2.6.0rc1-Instance-Auto

Added by Fabrice Barconnière almost 5 years ago. Updated almost 5 years ago.

Status:
Fermé
Priority:
Normal
Assigned To:
Start date:
03/02/2016
Due date:
% Done:

100%

Estimated time:
1.00 h
Spent time:
Remaining (hours):
0.0

Description

*** Test du module scribe version 2.6.0 (scribe 00000001) ***

Attention, serveur opérationnel mais des services ne sont pas démarrés :

quotaon.service loaded failed

L'erreur n’apparaît plus après reboot.

Associated revisions

Revision 0ac06023 (diff)
Added by Emmanuel GARETTE almost 5 years ago

le service quotaon ne doit pas être en erreur après instance (ref #17344 @1h)

Revision 68c985bf (diff)
Added by Emmanuel GARETTE almost 5 years ago

supprimer le status failed des services qu'on désactive (ref #17344 @1h)

Revision 1f1cf086 (diff)
Added by Emmanuel GARETTE almost 5 years ago

erreur dans le nom du service ... (ref #17344)

History

#1 Updated by Fabrice Barconnière almost 5 years ago

  • Subject changed from Scribe 2.6.0rc1 : Erreur au diagnose en utilisant le template etb1.scribe-2.6.0rc1-Instance-Auto to Scribe 2.6.0rc1 :Erreur au diagnose en utilisant le template etb1.scribe-2.6.0rc1-Instance-Auto
  • Description updated (diff)

#2 Updated by Emmanuel GARETTE almost 5 years ago

  • Status changed from Nouveau to En cours

#3 Updated by Emmanuel GARETTE almost 5 years ago

  • Assigned To set to Emmanuel GARETTE

#4 Updated by Emmanuel GARETTE almost 5 years ago

Si on n'active pas le serveur DHCP on a encore une erreur :

root@scribe:~# systemctl --state=failed
  UNIT                    LOAD   ACTIVE SUB    DESCRIPTION
● isc-dhcp-server.service loaded failed failed ISC DHCP IPv4 server

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.

1 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.
root@scribe:~# 

#5 Updated by Emmanuel GARETTE almost 5 years ago

  • % Done changed from 0 to 100
  • Remaining (hours) changed from 1.0 to 0.25

Pour tester :

Démarre un etb1.scribe "daily".

Les services isc-dhcp-server et quotaon sont en erreur :

root@scribe:~# systemctl --state=failed
  UNIT                    LOAD   ACTIVE SUB    DESCRIPTION
● eole-sso.service        loaded failed failed Eole Single Sign On server
● isc-dhcp-server.service loaded failed failed ISC DHCP IPv4 server
● quotaon.service         loaded failed failed Enable File System Quotas
● websockify.service      loaded failed failed EOP WebSocket to TCP proxy/bridge.

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.

4 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.
root@scribe:~# 
/root/mount.eole-ci-tests
cp /mnt/eole-ci-tests/configuration/etb1.scribe/default-2.6.0/etc/eole/config.eol /etc/eole/
CreoleSet activer_dhcp non
instance

Vérification :

root@scribe:~# systemctl --state=failed

Avant mise à jour on a :

root@scribe:~# systemctl --state=failed
  UNIT                    LOAD   ACTIVE SUB    DESCRIPTION
● isc-dhcp-server.service loaded failed failed ISC DHCP IPv4 server
● quotaon.service         loaded failed failed Enable File System Quotas

LOAD   = Reflects whether the unit definition was properly loaded.
ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
SUB    = The low-level unit activation state, values depend on unit type.

2 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.

Après mise à jour :

root@scribe:~# systemctl --state=failed
0 loaded units listed. Pass --all to see loaded but inactive units, too.
To show all installed unit files use 'systemctl list-unit-files'.

#6 Updated by Scrum Master almost 5 years ago

  • Status changed from En cours to Résolu

#7 Updated by Joël Cuissinat almost 5 years ago

  • Status changed from Résolu to Fermé
  • Remaining (hours) changed from 0.25 to 0.0

Testé OK

Also available in: Atom PDF